Keywords
stator core
assembly, pressing
specific pressure
control cell
plastic element
diaphragm with rigid center
strain gages турбогенератор
осердя статора
збирання
пресування
питомий тиск
контрольна комірка
пластичний елемент
мембрана з жорстким центром
тензорезистори
How to Cite
Abstract
A device for automated control by the stator core of a powerful turbine generator (TG) during assembly and pressing at the manufacturing plant is proposed. Using the device, places in the core with a weakened solidity are determined. For this, at N points evenly spaced along the cross section of the stator core, the specific pressing pressure of special plastic elements, which are installed in the control cells of the additional pressure ring of the press, on which the core is assembled, is measured. During pressing, the elements are deformed, and their deformation depends on the degree of core defect (decrease in solidity) in the zone of which they are located. The sample will be deformed less, located in the zone of the largest defect, and most of all - in the zone where the defect is minimal. The pressure is measured using a flat metal membrane with a rigid center on which strain gauges are located at selected points. It is shown that the relative deformations in a flat membrane, which are measured by strain gages, depend on the value of the specific pressing pressure. Analytical relationships between the relative radial and tangential deformations and the specific pressing pressure have been determined. References 20, figures 5.
References
Yukhimchuk V.D. Technology for the production of electrical machines. Kharkiv: Timchenko, 2006. 543 p. (Rus)
Patil A., Biswas S. Modeling a virtual prototype of stator core lamination assembly device. International Journal of Electrical, Electronics and Data Communication. 2013. Vol. 1. Issue10. Pp. 32–35.
Geddam P., Barik B.K. Developing a virtual prototype for stacking laminations in stator core of turbogenerator using robot simulation software. Journal of Material Science and Mechanical Engineering (JMSME). 2015. Vol. 2. No 5. Pp. 456–460.
Fomin B.P., Tsikhanovich B.G., Viro G.M. Technology of large electrical machine building. Turbine generators. Vol. 1. Leningrad: Energoatomizdat, 1981. 303 p. (Rus)
Zaitsev I.O., Panchik M.V. Physical processes and their influence on the evolution of defects in the powerful generators stator core. Science and Education a New Dimension. Natural and Technical Sciences. 2020. Issue 224. Pp. 81–84. DOI: https://doi.org/10.31174/SEND-NT2020-224VIII27-20 (Rus)
Puzakov S.E., Golodnova O.S., Rostik G.V., Kutukov L.G., Zavialov G.V., Tkachev L.N. Handbook for the repair of turbine generators. Moskva: IPK gossluzhby, VIPKenergo, 2006. 724 p. (Rus)
Alekseev B.A. Determination of the state (diagnostics) of large turbine generators. Moskva: Publishing house NTs ENAS, 2001. 152 p. (Rus)
Stator core compressibility test. URL: https://www.slideshare.net/donaldsatrianistephen/stator-core-compr-test (accessed 10.06.2020).
Grigoriev A.V., Semenov D.Yu., Osotov V.N., Yampolskiy D.A. Investigation of vibromechanical characteristics of a package of electrical steel and the possibilities of their use to control the pressing of the stator core of a turbine generator. Elektrotekhnika. 2003. No 8. Pp. 36–41. (Rus)
Grigoriev A.V., Osotov V.N., Yampolsky D.A. Application of the vibration energy absorption parameter to control the pressing of stators cores of turbogenerators. Elektrotekhnika. 2004. No 11. Pp. 16–19. (Rus)
Sharonin V.S., Poltoradnia A.V. Method for diagnosing the state of the stator core of an electric machine. Patent RU No 2223587, 2004. (Rus)
Zaitsev Ie.O., Levytskyi A.S., Kromplyas B.A. Capacitive distance sensor with coplanar electrodes for large turbogenerator core clamping system. IEEE 39th International Conference on Electronics and Nanotechnology (ELNANO), Kyiv, Ukraine, April 16 – 18, 2019. Pp. 644-647. DOI: https://doi.org/10.1109/ELNANO.2019.8783916
Levitskyi A.S., Zaitsev Ie.O., Kobzar K.A. Measuring the stroke of cone disk springs in power accumulators of the turbogenerator stator core using a capacitive sensor. Pribory I metody izmereniia. 2018. Vol. 9 (2). Pp. 121-129. DOI: https://doi.org/10.21122/2220-9506-2018-9-2-121-129 . (Rus)
Pinskoy V.F., Zakhozhaev V.M., Shoful A.K., Levitskyi A.S. Monitoring of the stator of a forced turbine generator for an hour when folding and pressing. Hydroenergetika Ukrainy. 2020. No 1-2. Pp. 55–58. (Ukr)
Andreeva L.E. Elastic elements of devices. Moskva: Mashinostroenie, 1981. 392 p. (Rus)
Skvortsov P.A. Development of a method for calculating and designing an elastic element of a strain gauge on the structure "Silicon on sapphire": author’s abstract of cand. tech. Sci. diss.: 01.02.06. Moskva, 2019. 20 p. (Rus)
Tinyakov Yu.N., Nikolaneva A.S. On the calculation of pressure sensor membranes. Vestnik MGTU im. N.E. Bauman. Ser. Priborostroenie. 2015. No 6. Pp. 135–142. DOI: https://doi.org/10.18698/0236-3933-2015-6-135-142 (Rus)
Bauman E. Measurement of forces by electric methods. Moskva: Mir, 1978. 430 p. (Rus)
Dan Mihai Stefanescu. Handbook of Force Transducers: Principle and Components. Berlin: Springer, 2011. 612 p. URL: https://books.google.com.ua/books?id=RjzO10gmXZYC&pg=PR21&lp (accessed 10.06.2020).
Guide to the Measurement of Force. The Institute of Measurement and Control, London. Originally published 1998. Reviewed and re-issued. 2013. 46 p. URL: http://www.npl.co.uk/upload/pdf/forceguide.pdf (accessed 10.06.2020).
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Copyright (c) 2021 Array